gadepiahospigchi.netlify.com

Can anyone comment on RSP redundancy with SSO mode?

C6816-X-LE#sh hw-module slot 1 oversubscription port-group oversubscription-mode 1 enabled 2 disabled The Catalyst 6840-X series chassis provides extremely high levels of scalability and performance, with the size and economics of an innovative fixed architecture. Fw-01# hw-module module 1 reset The module in slot 1 should be shut down before resetting it or loss of configuration may occur. Reset module in slot 1? confirm Reset issued for module in slot 1 Now you need to wait for a while (about 2 minut es during Initialization state): fw-01# show module 1 details.

I have a test 7507 with rsp-k4pv-mz.120-32.S8.bin on both RSP2s. I've done
this:

Symptom: SIP remains in disabled state even if 'no hw-module slot X shutdown' command is entered in order to undo the previosly configured 'hw-module slot X shutdown' (config)#no hw-module slot X shutdown #show platform Slot Type State Insert time (ago) - - - - X ASR1000-SIP10 disabled 2d03h Conditions: 'hw-module slot X shutdown' was configured multiple times on the same slot. Router#show hw-module interface g0/0/0 transceiver status The Transceiver in slot 0 subslot 0 port 2 is enabled. Sensor Data is not supported by this transceiver.

service single-slot-reload-enable
redundancy
no keepalive-enable
mode sso
And it doesn't seem to ever sync the slave
ranttest#show red
Redundant System Information :
------------------------------
Available system uptime = 14 minutes, 49 seconds
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = hsa
Maintenance Mode = Disabled
Communications = Down Reason: Simplex mode
Current Processor Information :
-------------------------------
Active Location = slot 2
Current Software state = ACTIVE
Uptime in current state = 13 minutes, 24 seconds
Image Version = Cisco Internetwork Operating System
Software
IOS (tm) RSP Software (RSP-K4PV-M), Version 12.0(32)S8, RELEASE SOFTWARE
(fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Mon 20-Aug-07 16:34 by leccese
BOOT =
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Peer (slot: 3) information is not available because it is in 'DISABLED'
state
ranttest#redundancy force-switchover
Cannot perform switchover until the standby is fully initialized.
The box is up, its got two OSPF adjacencies, maybe a hundred routes - its
not doing anything fancy, so I'm kind of stuck here. The production target
is 7507s /w RSP4s, the same OSPF, and about 180k routes via BGP. Any idea
what might be wrong here?
_______________________________________________
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/My wonderful Kiwi Cattools is doing configuration backup of devices every 15 minutes. Two times till now it happened to me that different ASA SSM modules are stopping to respond on ssh configuration requests.
After getting the status of the module; the status show up as: Unresponsive
fw-01# show module 1 details
Getting details from the Service Module, please wait...
Unable to read details from slot 1
ASA 5500 Series Security Services Module-20
Model: ASA-SSM-20
Hardware version: 1.0
Serial Number: JAF1535CKBP
Firmware version: 1.0(11)5
Software version: 7.1(6)E4
MAC Address Range: 44d3.ca8e.06f8 to 44d3.ca8e.06f8
App. name: IPS
App. Status: Not Applicable
App. Status Desc: Not Applicable
App. version: 7.1(6)E4
Data plane Status: Not Applicable
Status: Unresponsive
Only way to do it is to reset the module using command:

hw-module module 1 shutdown

Shutdown module in slot 1? [confirm]
Shutdown issued for module in slot 1

fw-01# show module 1 details
Getting details from the Service Module, please wait...
Unable to read details from slot 1
ASA 5500 Series Security Services Module-20
Model: ASA-SSM-20
Hardware version: 1.0
Serial Number: JAF1535CKBP
Firmware version: 1.0(11)5
Software version: 7.1(6)E4
MAC Address Range: 44d3.ca8e.06f8 to 44d3.ca8e.06f8
App. name: IPS
App. Status: Not Applicable
App. Status Desc: Not Applicable
App. version: 7.1(6)E4
Data plane Status: Not Applicable
Status: Down

fw-01# hw-module module 1 reset
The module in slot 1 should be shut down before
resetting it or loss of configuration may occur.
Reset module in slot 1? [confirm]
Reset issued for module in slot 1

No Hw-module Slot 1 Oversubscription

Now you need to wait for a while (about2 minutes during Initialization state):
fw-01# show module 1 details
Getting details from the Service Module, please wait...
Unable to read details from slot 1
ASA 5500 Series Security Services Module-20
Model: ASA-SSM-20
Hardware version: 1.0
Serial Number: JAF1535CKBP
Firmware version: 1.0(11)5
Software version: 7.1(6)E4
MAC Address Range: 44d3.ca8e.06f8 to 44d3.ca8e.06f8
App. name: IPS
App. Status: Not Applicable
App. Status Desc: Not Applicable
App. version: 7.1(6)E4
Data plane Status: Not Applicable
Status: Init
After about 2 minutes you will get correct status output for SSM module:
fw-01# show module 1 details
Getting details from the Service Module, please wait...
ASA 5500 Series Security Services Module-20
Model: ASA-SSM-20
Hardware version: 1.0
Serial Number: JAF1535CKBP
Firmware version: 1.0(11)5
Software version: 7.1(6)E4
MAC Address Range: 44d3.ca8e.06f8 to 44d3.ca8e.06f8
App. name: IPS
App. Status: Up
App. Status Desc: Normal Operation
App. version: 7.1(6)E4
Data plane Status: Up
Status: Up
Mgmt IP addr: 10.10.212.21
Mgmt Network mask: 255.255.255.0
Mgmt Gateway: 10.10.212.1
Mgmt Access List: 10.20.150.0/23
Mgmt Access List: 10.30.150.0/23
Mgmt web ports: 443
Mgmt TLS enabled: true

Hw-module Session

Useful links:

Cisco Hw-module Slot

1. Configuring the ASA 5500 AIP SSM
2. Configuring the ASA 5500 AIP SSM - PDF

Hw-module Location 0/0/cpu0 Port-mode